Japan has set an MCCP impurity limit of 3% by weight under the Chemical Substances Control Law (CSCL). MCCPs are medium-chain chlorinated paraffins. The limit comes with the Class I ban that took effect on 22 November 2026. It also sits beside existing limits for PCBs, HCB and SCCPs. These are polychlorinated biphenyls, hexachlorobenzene and short-chain chlorinated paraffins. So importers and makers should check their products now.
What Happened
Japan’s Cabinet approved a Cabinet Order on 19 May 2026, and it was promulgated on 22 May. It designates MCCPs, chlorpyrifos (an insecticide) and long-chain PFCAs (perfluorocarboxylic acids) as Class I Specified Chemical Substances. In the order, MCCPs mean C14–17 chlorinated paraffins with chlorine content of 45% by weight or more. The designations took effect on 22 November 2026.
Class I status bans manufacture and import in principle. However, the three ministries (the Ministry of Economy, Trade and Industry, the Ministry of Health, Labour and Welfare, and the Ministry of the Environment) allow trace amounts as impurities under the best available technology (BAT) principle. Next, a notice of 31 March 2026 set limits for PCBs (50 ppm, or parts per million), HCB (200 ppm in tetrachlorophthalic anhydride, TCPA, and 10 ppm in pigments or dyes made from it) and SCCPs (below 1% by weight, or 10,000 ppm).
For MCCPs, the ministries set the reference value at 3% by weight, which is 30,000 ppm. A document of 24 July 2026 gives this level, the same as the Stockholm Convention limit. A final MCCP notice was issued on 26 October 2026 and took effect on 27 October 2026. Even so, businesses should cut MCCP content as far as is feasible below 3%.
What’s New
- MCCP impurity reference value: 3% by weight (30,000 ppm).
- PCB limit: 50 ppm.
- HCB limit: 200 ppm in TCPA and 10 ppm in pigments or dyes made from it.
- SCCP limit: below 1% by weight (10,000 ppm).
- MCCPs, long-chain PFCAs and chlorpyrifos became Class I on 22 November 2026.
Key Dates & Timeline
Who and What Is in Scope
Industries: Automotive components · Plastics and rubber · Wire and cable · Electronics · Paints and coatings · Chemicals
Who is affected: Importers and makers of chemicals and articles that sell in Japan. Suppliers of plastics, sealants, cables and lubricants are affected too.
Products and standards in scope: Chemical substances and products that contain PCBs, HCB, SCCPs or MCCPs as unintended contaminants.
Requirements and restrictions: From 22 November 2026, manufacture and import of Class I substances is banned in principle. Impurities within the limits are allowed if companies manage them under BAT and document this in advance.
What Companies Should Do
- Test products against the PCB, HCB, SCCP and MCCP limits.
- Next, ask suppliers for MCCP and SCCP data.
- Also file BAT documentation where you need it.
- Finally, confirm that your products meet the Class I rules that apply since 22 November.
The Class I ban has applied since 22 November. So test your products and collect supplier data now.
Related: Japan Tightens Chemical Rules on PFAS and Chlorpyrifos
METI — Cabinet decision on the amended CSCL Enforcement Order — https://www.meti.go.jp/english/press/2026/0519_002.html
METI — MCCP impurity reference value (24 July 2026, Japanese) — https://www.meti.go.jp/shingikai/kagakubusshitsu/anzen_taisaku/pdf/2026_01_02_00.pdf
Reach out to our regulation experts on chemical and product regulatory compliances
































